THE CANVAS TENT.

[Ill.u.s.tration: Fig. 38. The Sail St.i.tch.]

When at last spring arrived and we returned to Lamington on our Easter vacation, quite a sum of money had been collected, nearly $15.00, if I remember rightly; at any rate plenty to buy the materials for a good-sized tent and leave a large surplus for provisions, etc. Bill figured out on paper just how much canvas we would need for a tent 7 feet wide by 9-1/2 feet long, which he estimated would be about large enough to hold us. It took 34 yards, 30 inches wide. Then we visited the village store to make our purchase. Canvas we found a little too expensive for us, but a material called drill seemed about right. It cost ten cents a yard, but since we wanted such a quant.i.ty of it the price was reduced to a total of $3.00. We repaired to the attic to lay out the material.

[Ill.u.s.tration: Fig. 39. Cutting out the Door Flaps.]

[Ill.u.s.tration: Fig. 40. Sewing on the Door Flaps.]

First we cut out four lengths of 5 yards and 26 inches each. The strips were basted together, lapping the edges 1 inch and making a piece 17 feet 2 inches long by 9 feet 9 inches wide. Mother sewed the breadths together on the machine, using a double seam, as in sail making; that is, two parallel rows of st.i.tching were sewed in, one along each overlapping edge, as shown in Fig. 38. A 1-inch hem was then turned and sewed at the ends of the goods, so that the piece measured exactly 17 feet long. It served for the roof and side walls of the tent. Our next operation was to cut three strips 11 feet long, and sew them together with a double seam as before. This piece was now slit along the center line _m_, Fig. 39, making two lengths 3 feet 8 inches wide. The strips were then cut along the diagonal lines _a a_, forming the end walls or doors, so to speak, of the tent. In sewing on the door flaps we started first at the bottom of the side _c_, sewing it to the side edge of the main piece, as shown in Fig. 40, and running the seam up for a distance of exactly 3 feet 6 inches. After all the door strips had been sewed along their _c_ edges the sewing was continued up the diagonal or _a_ edges. In cutting out the door pieces we had allowed 1 inch on each side for hems and seams, so that the door pieces met without lapping at the exact center of the main or body piece, that is, at the peak of the tent.

[Ill.u.s.tration: The Wall Tent Set Up in the Back Yard.]

[Ill.u.s.tration: Fig. 41. Adjustable Ridge Pole.]

[Ill.u.s.tration: Fig. 42. The Tent Set Up.]

Our next step was to fasten the necessary ropes and loops. Ten 8-foot lengths of light rope were procured. These were fastened at the top of the side walls, that is, 3 feet 6 inches from the ends of the main or body piece, one at each corner and one on each seam. The cloth was strengthened at these points with patches sewed on the inside. At the bottom of the side walls we sewed on loops of heavy tape. These were s.p.a.ced about 15 inches apart. Along the _b_ edges of the door pieces tie strings of tape were fastened. A rope 15 feet long was attached to the peak at the front and at the rear of the tent. The front and rear posts of the tent were made from scantlings measuring 2 by 4 inches, which were procured from Mr. Schreiner's lumber yard. They were planed smooth and sawed off to a length of 7 feet 6 inches. A slot was cut in the end of each stick to a depth of 6 inches and measuring slightly over an inch in width. For the ridge pole a strip 1 inch thick, 2-1/2 inches wide and 10 feet long was secured. This was fitted into the slotted ends of these posts, where it was fastened by wooden pegs slipped into holes drilled through the ends of the posts and the ridge pole. A number of these peg holes were provided, so that if the canvas stretched the ridge pole could be raised or lowered to prevent the walls from dragging on the ground. We set up the tent in our back yard to see if it was properly constructed. Twelve stakes were required, ten for the sides and one for the ridge stays at the front and rear. The side stakes were driven into the ground at a distance of about 8 feet from the center of the tent. First we tied the guy ropes to the stakes, but later we found it much easier to secure them with tie blocks.

TIE BLOCKS.

[Ill.u.s.tration: Fig. 43. The Wood Tie Block.]

[Ill.u.s.tration: Fig. 44. The Wire Tie.]

[Ill.u.s.tration: Fig. 45. Bottom of Tent Wall.]

These were made of wood 1/2 inch thick, 1 inch wide and each measured 3 inches long. A hole was drilled into the block at each end and through these holes the rope was threaded. A knot in the rope then held the end from slipping out. The loop between the two holes, or the bight, as sailors would call it, was now slipped over the stake, and the rope hauled tight by drawing up the tie block, as shown in Fig. 43. A still later improvement consisted in making ties of stout galvanized iron wire, bent to the form shown in Fig. 44. The wooden ties were apt to swell and split open when exposed to the weather, while the wire ties could always be relied upon.

The walls of the tent were held down along the bottom by railway spikes hooked through the tent loops and driven into the ground. Wooden pegs with notches to catch the loops would have served as well, but Dutchy happened to find a number of the spikes along the track and in his usual convincing manner argued that they were far better than pegs because their weight would hold the cloth down even if they were not firmly embedded in the ground.

THE ANNEX.

We were surprised to find out how small the tent was after it was set up. We could see at once that when we had put in all the stores and provisions we would need, there would not be room enough for six boys and a man to stretch themselves out comfortably in it. Bill had evidently made a miscalculation, but he suggested that we remedy the error by building an annex for our kitchen utensils and supplies.

[Ill.u.s.tration: Fig. 46. Cutting out the Annex.]

[Ill.u.s.tration: Fig. 47. The Annex Applied.]

This gave us a two-room tent, which we found to be quite an advantage.

Twelve more yards of drill were bought and cut into two strips, each 17 feet 2 inches long. The breadths were then sewed together, and the ends turned up and hemmed to make a piece 17 feet long and 4 feet 9 inches wide. Tape loops were then sewed on as before, and ropes were fastened on at the top of the side walls, that is, 3 feet 6 inches from the ends of the strips. We thought it would be better to have a slanting ridge on the annex, so we cut out a wedge-shaped piece from the center of the two strips, as shown by dotted lines _B B_ in Fig. 46. This wedge-shaped piece measured 2 feet at the outer end of the annex, and tapered down to a point at the inner end. The canvas was then sewed together along these edges. Tie strings were sewed to the inner edge of the annex and corresponding ones were attached to the main tent a little ways back from the edge, so that the two could be tied together, with the annex lapping well over on the roof and side walls. A notch was cut out of the peak of the annex, so that it could be tied around the rear post of the tent, and notches were cut at the top of the side walls to permit pa.s.sing the cloth around the wall ropes. Instead of supporting the ridge of the annex on a ridge pole, we used the rear guy line of the tent, propping it up with a scantling about 5-1/2 feet long.

CHAPTER V.

PREPARING FOR THE EXPEDITION.

School closed on the 21st of June that year, just ten days before the expected arrival of Uncle Ed. The first thing we did was to set up our tent in the back yard and camp out so as to become acclimatized. It is good that we did this, for the very first night a heavy summer shower came up which nearly drenched us. The water beat right through the thin canvas roof of our tent. Had we been able to afford the best quality of canvas duck, such an occurrence would probably have been avoided. But we solved the difficulty by using a tent fly; that is, a strip of canvas stretched over the tent and s.p.a.ced a short distance from it to break the fall of the rain drops.

[Ill.u.s.tration: Fig. 48. The Wall Tent with the Fly fastened on.]

TENT FLY.

[Ill.u.s.tration: Fig. 49. The Fly Ridge Pole.]

Again we had to visit the village storekeeper; this time we bought out his whole remaining stock, sixteen yards of drill. This was cut into four-yard strips, which were sewed together as before and the ends turned up and hemmed. Tie strings were sewed to the ends of the strips so that the fly could be tied to the wall ropes of the tent. At the ridge the fly was supported about six inches above the tent rope by a second ridge pole held by pegs in the top holes of the tent posts.

PROVISIONS AND SUPPLIES.

The ten days before Uncle Ed arrived were busy indeed. We had to gather together the necessary provisions and supplies. Our personal outfits were very simple. Each member supplied himself with a change of underwear, a bathing suit, a blanket and a toothbrush. A single comb and brush served for the entire society, and was used on Sundays, the only day we really dressed up. All the rest of the time we lived in our bathing suits, except, of course, on cold rainy days. Our kitchen outfit consisted of a large cooking pot, two kettles, a frying pan, a coffee pot, a small oil stove, a half-dozen each of plates, cups, saucers, knives and forks, a dozen spoons, two tablespoons, and, in addition, several large plates and bowls for pantry use. We also took with us a dish-pan and several dish-towels. For our larder we collected the following: A bag of flour, ten pounds of sugar, two pounds of salt, three pounds of coffee, four pounds of oatmeal, four pounds of b.u.t.ter, two pounds of lard, six pound of beans, six pounds of rice, three pounds of bacon, six cans of condensed milk, a dozen eggs, box of pepper, and several jars of canned peaches and pears, and also a half dozen gla.s.ses of jelly.

It was Dutchy who suggested that we have a chicken yard, in connection with our camp, to supply us with fresh eggs. It was a capital idea, and by the dint of some coaxing we managed to secure the loan of a half dozen hens and a rooster.

Our miscellaneous list included a spade, pick and shovel, an ax, a hatchet, two large pails, a barn lantern, a can of kerosene, a dozen candles, a cocoa box filled with matches, a pair of scissors, needles, b.u.t.tons, pins and safety pins, a spool of white and another of black cotton, fishing tackle, a roll of heavy twine, a coil of rope, and a set of dominoes and checkers. But most important of all was a chest of tools belonging to Reddy. These were all collected when Uncle Ed arrived.

Dutchy also contributed a large compa.s.s, which we found very useful later on, for surveying the island.

CROSSBOW.

Reddy had a shotgun which he wanted to bring along, but my father, and Dutchy's as well, wouldn't let us go camping if there was to be any gunpowder along, so we had to leave it behind. Of course we didn't miss it at all when we got to the island, because there was so much else to do; but we all agreed with Dutchy, that "it wouldn't be no sort of a scientific expedition without takin' a gun along." As a subst.i.tute I suggested a bow and arrow. They all laughed at such a "kiddish" idea; all but Bill, I mean.

[Ill.u.s.tration: Drifting down the Schreiners' Brook.]

[Ill.u.s.tration: Paddling in the Old Scow.]

[Ill.u.s.tration: Fig. 50. Binding the Bow.]

[Ill.u.s.tration: Fig. 51. The Trigger.]

[Ill.u.s.tration: Fig. 52. The Trigger Set for Firing.]

[Ill.u.s.tration: Fig. 53. The Umbrella Rib Crossbow.]

"It ain't such a bad notion," said he, "only a crossbow would be better.

I've seen them made out of umbrella ribs so they'd shoot like greased lightning." Of course we had to have one of these wonderful weapons.

Down in the ash heap we found two broken umbrellas with 27-inch ribs.

Bill selected ten good ribs, from which he wrenched off the spreaders with a pair of pliers. The ribs were then bound together by winding stout twine around them. The winding was very evenly and closely done, so that the cord completely covered the ribs, making a solid rod of spring steel. But before winding we had laid in between the ribs a piece of heavy twine, to which the bowstrings could be tied after the bow was all wound. The stock of our crossbow was cut out of a board of soft wood 1 inch thick to as near the shape of a gun as we could get it. A hole was drilled through the muzzle end to receive the bow, and then the bowstring was tied fast. Along the upper edge of the barrel a V-shaped channel was cut. The channel was not very deep, only enough to receive a tenpenny nail with the head projecting half-way above the sides. A notch was cut across the barrel, through this channel, at the trigger end, and a trigger made of heavy iron wire, bent to the shape shown in Fig. 51, was hinged to the gun by a bolt which pa.s.sed clear through the stock and through both eyes of the trigger. By using two nuts on the bolt, and tightening one against the other, they were prevented from working loose and coming off. When we wanted to fire the gun the bowstring was drawn back, and held by slipping it into the notch, and a nail was laid in the channel with its head against the bowstring. Then, on pulling the trigger, the bowstring was lifted out of the notch, and sent the nail off sailing. The long-grooved barrel insured a very good aim.

MEGAPHONE.