Electricity for the 4-H Scientist - Part 18
Library

Part 18

A policeman uses his brain to tell him when to blow his whistle, but a fuse depends on the size of the little fusible (meltable) metal link that you see under the gla.s.s.

If too great an electrical load is added to a circuit, this link will melt and prevent a dangerous overload. If you put in a fuse with too heavy a link, it will not melt in time, and the wiring and equipment may be damaged.

Therefore the right size of fuse is very important, and is something that you should check in your own home.

See the chart above for the right fuse for each size wire.

Make a Circuit Chart

At one or more places in your home there is a box or panel containing the fuses or breakers for the various circuits. Attached to the inside of the door of each such panel should be a chart something like this:

[Ill.u.s.tration]

+-----+---------------------+-----------+ | No. | Description | Fuse size | +-----+---------------------+-----------+ | 1 | Range | 40 | +-----+---------------------+-----------+ | 2 | Kitchen Outlets | 20 | +-----+---------------------+-----------+ | 3 | Dining Room Outlets | 20 | +-----+---------------------+-----------+ | 4 | Living Room Outlets | 15 | +-----+---------------------+-----------+ | | | | +-----+---------------------+-----------+ | | | | +-----+---------------------+-----------+

Notice that in our chart we have made columns for a description of what each circuit serves, its number or position in the panel, and the proper size fuse for it.

Because most such charts leave out this last very important bit of information, you should make a complete new chart, like the one shown.

Provide as many lines as there are fuse positions. Paste or tape it to the inside of the panel door.

Then, ask permission of your parents to disconnect all the circuits by uns.c.r.e.w.i.n.g the fuses or flipping the circuit breakers. _Do not touch anything but the fuse rim._ Then reconnect them, one at a time, to find out what each circuit serves. Turn on as many lights as you can, to help you in your detective work. Use a test lamp at those outlets that do not have a light connected to them. Write two or three words describing each circuit on the proper line on your chart.

On a separate sheet, keep track of the appliances and lights that are on each circuit, and add up the watts. (If the name-plate of any appliance gives "amperes", "amps", or "A" instead of watts, just remember that amps times volts equals watts.) This will tell you if any of them are overloaded. Show this sheet to your parents.

Check the Wire Sizes

_Disconnect the main switch_, and determine the size of the wires in each circuit. Don't include the insulation in your measurement.

_BE CAREFUL!

Even though you have disconnected the main switch, the wires coming into it are still "live". So, do not touch any wires. Instead hold the wire size chart near them so that you can tell which gauge each one is._

Write in the proper size fuse for each circuit on your chart.

Replace Any Wrong-Size Fuses

Do the fuse sizes you have written on your chart agree with the ones that are in place in the panel?

Get the right size fuses and replace any that are wrong. Make sure that you have a reserve supply of the right sizes, and that they are handy for future use.

Talk it Over With Your Parents

Do you think that your home has enough of the proper size circuits? If not, talk it over with your parents. They may want to ask an electrician to go over the wiring and make the necessary changes.

What Did You Learn?

(Underline the right answer.)

1. A (television set, radio) is very sensitive to changes in voltage.

2. Dimming lights mean (static in the wires, an electrical overload).

3. Wires that become warm from overload make it (more expensive, cheaper) to operate the equipment.

4. A home of 2,000 sq. ft. should have at least (three, four) general purpose circuits.

5. One solution to low voltage symptoms is (heavier fuses, more circuits).

6. Full capacity for a Number 14 wire circuit at 115 volts is (1725 watts, 3000 watts).

7. A room air conditioner should be on (a general purpose, an individual) circuit.

8. The purpose of a fuse is to (let you disconnect the circuit, automatically prevent overloading the circuit).

9. The right size fuse is determined by (wire size, the store where you buy it).

10. A circuit chart should give (circuit description and fuse size, the maker's name).

Demonstrations You Can Give

Ask your leader to help you plan a demonstration. You can show how lights dim when too many other appliances are connected, how a fuse protects against overloading, and the danger of using too large a fuse.

For More Information

Ask your Extension agent, power supplier, or electrician for additional help.

LESSON NO. B-15

Credit Points 4

YOU CAN MEASURE ELECTRICITY

Instruments that can detect or measure the flow of electricity have helped to make possible the wonders of electricity as we know them today.

Scientists in laboratories must have measuring devices for experiments leading to new uses of electricity. Power suppliers must have instruments that tell what the generating equipment is doing and to measure the amount of electricity being sold to users. Factories need instruments that keep tab on electrical equipment to make sure electricity is being used efficiently.