They are generally set in thickets or woods where either rabbits or partridges are known to abound. Having arrived at his chosen trapping ground, the young trapper should first select some slender, elastic sapling; that of the hickory is the best, and is generally to be found in open woods--if not, some other kind will answer very well. It should be about five or six feet in length, (trimmed of its branches,) and in diameter need be no larger than an axe-handle or a broom-stick. When this is decided, some spot about five feet distant from the sapling should then be selected. The hatchet and knife will now come into excellent use, in cutting the sticks for the little inclosure shown [Page 45]

in our drawing. This should be about eight or ten inches in diameter, and of about the same height. The sticks should be driven into the ground in a circle, leaving an open s.p.a.ce of about six inches on one side. A stout switch as large as a man's little finger, and nearly two feet long, should then be cut and nicely sharpened at both ends. This should then be driven into the ground in the form of an arch, at the opening of the inclosure.

We will now ask our readers to turn their attention to the next ill.u.s.tration, in order to understand what is to follow. This picture shows the method of setting the trap.

[Ill.u.s.tration]

After the arch is firmly fixed in its place, a short piece of stick should be cut, of a length corresponding to the height of the arch.

To the middle of this stick the bait should be attached, being either tied to it or stuck on a plug driven into the stick, the latter being sharpened on one end. Next proceed to cut another stick, of about six inches in length; let this be flattened on one end. The wire noose should then be fastened to the opposite end. The noose in this case should be large enough to fill the opening of the arch. We will now go back to the sapling again.

It should be bent down slightly, and a piece of the strong twine should be tied to its tip. Taking hold of the string, proceed to bend down the end of the sapling, in the direction of the inclosure, until it draws with a force strong enough to lift a rabbit if he were tied to the end of it. Thus holding it down with the string against the front of the inclosure, cut off the twine at the place where it crosses the top of the arch, as this will be the required length. It is now necessary to tie the end of this string to the same piece of wood and at the same place to which the noose was tied. When this is done the trap may be set as shown in the cut.

The spring sapling should be bent as seen in the first ill.u.s.tration.

The piece of wood holding the noose should be pa.s.sed beneath the top of the arch, as far as it will go, with its long end pointing inside the inclosure. By now supporting the inside end with the bait stick, and carefully adjusting the noose so as to completely fill the arch, the trap will be set.

[Page 46]

In order to reach the bait, the rabbit or bird _must_ necessarily pa.s.s its head through the noose, after which, if the bait be scarcely _touched_, the animal's doom is sealed, and he is lifted into the air, generally suffering almost instant death. It is well known that in the case of a rabbit the neck is broken by a very slight blow, a strong snap of the finger being often sufficient. It is therefore safe to conclude that when thus suddenly caught and lifted by the noose, death must occur almost instantaneously from the same cause.

It is not really necessary for success that the force of the sapling should be strong enough to lift the rabbit from the ground, as a mere strong tightening of the noose would be sufficient to cause strangulation and death. But we recommend the former method as being less painful and more rapid in its effects.

If the young trapper should experience any difficulty in finding saplings of the right size, in the locality where he desires to set his traps, the difficulty may be easily mended by cutting the poles elsewhere, and carrying them to his trapping-ground, this answering the purpose equally well. They should be sharpened nicely on the large end, and firmly stuck into ground. The "Twitch-up"

may be used for the capture of all varieties of game, and when set with the noose in the opening of a hollow tree, a stray c.o.o.n will occasionally be entrapped.

The next figure represents another method of constructing this trap, The picture explains itself. Instead of the arch, two notched sticks are driven into the ground, one on each side of the opening of the pen, The other piece should be of the shape shown in the figure, made either in one piece or in two pieces fastened together.

They may all be constructed from twigs in the woods. Let the noose and draw-string now be fastened to the middle of the cross piece, and when set it will appear as in our figure. It will easily be seen that a slight pull on the bait will turn the cross piece from beneath the notches, and allow it to fly into the air.

[Ill.u.s.tration: Method No. 2]

In our next instance the same principle is employed. The [Page 47]

notched pegs are here driven in the back part of the pen, about five inches apart, with their notches towards the front. A forked bait stick of the shape shown is then procured. The draw-string should be attached near the end furthest from the fork. By now inserting the ends lightly beneath the notches in the pegs, at the same time letting the bait incline near the ground, the trap will be set on a very slight lift, as the bait will dislodge the pieces. Of course the noose must be arranged in the opening of the pen, as in the previous varieties. The bait stick in both cases should be set cautiously beneath the notches, as shown at (_a_), so that the slightest turn will cause it to roll out of position.

[Ill.u.s.tration: Method No. 3]

A fourth method of snaring is shown in our next figure. In this instance the original arch is used, or else some circular opening constructed in the front of the pen. Inside, at the back part of the inclosure, a smaller arch is placed. Two sticks are then to be made similar to those mentioned in our first example of the "Twitch-up." Let the draw-string be tied to the end of one of these sticks; after which it should be pa.s.sed under the inside arch, being brought out in front of it, and there supported by the bait-stick, as seen in our ill.u.s.tration. The noose should then be attached to the draw-string above the pen, and afterward brought down and arranged in front of the opening. The trap is then set, and will be found on trial to work admirably.

[Ill.u.s.tration: Method No. 4]

One of the simplest as well as _surest_ of "Twitch-up" traps forms the subject of our next ill.u.s.tration. Like the foregoing varieties it is of course to be surrounded by its pen, and supplied with a circular opening or arch at one side, in which to hang the noose.

It is constructed of three twigs. A simple crotch (_a_) should be firmly inserted in the ground at [Page 48]

the back part of the pen; (_b_) the bait stick, consists of a straight twig, five or six inches in length, and should be attached to the draw-string at about half an inch from the large end; (_c_) is another forked stick with unequal arms, the long one being driven into the ground near the opening of the pen and a little to one side, letting the remaining arm point directly towards the crotch-stick at the back of the pen. The noose having been attached to the draw-string, the trap may now be set. Lower the bait stick and pa.s.s the large end under the crotch at the back of the pen, catching the baited end underneath the tip of the forked stick near the pen's opening. Arrange the noose in front of the entrance, and the thing is done. A mere touch on the bait will suffice to throw the pieces asunder. It is an excellent plan to sharpen the point of the forked stick (_c_) where it comes in contact with the bait stick, in order to make the bearing more slight, and consequently more easily thrown from its balance.

[Ill.u.s.tration: Method No. 5]

THE POACHER'S' SNARE.

Our next example represents one of the oldest and best snares in existence,--simple in construction, and almost infallible in its operations. It is the one in most common use among the poachers of England, hence its name. The pieces are three in number, and may be cut from pine wood, affording easy and profitable employment for the jack-knife during odd hours and rainy days, when time hangs heavily.

The pieces are so simple in form and easy of construction that a sufficient number for fifty traps might be whittled in less than two hours, by any smart boy, who is at all "handy" with his jack-knife.

If a few good broad shingles can be found, the work is even much easier,--mere splitting and notching being then all that is necessary.

The bait stick should be about eight inches long, pointed at one end, and supplied with a notch in the other at about half an inch [Page 49]

from the tip. The upright stick should be considerably shorter than the bait stick, and have a length of about ten inches, one end being nicely pointed, and the broad side of the other extremity supplied with a notch similar to the bait stick. About four inches from the blunt end, and on the narrow side of the stick, a square notch should be cut, sufficiently large to admit the bait stick loosely. The catch piece now remains. This should be about two and a-half inches in width, and bevelled off at each end into a flat edge. The shapes of the different pieces, together with their setting, will be readily understood by a look at our ill.u.s.tration.

[Ill.u.s.tration]

A hundred of these pieces will make a small bundle, and may be easily carried by the young trapper, together with his other necessaries, as he starts off into the woods. He will thus be supplied with parts for thirty-three traps, all ready to be set, only requiring the stakes for the pens, which may be easily cut in the woods. Having selected a flexible sapling about five feet in length, and having stripped it of its branches, proceed to adjust the pieces. Take one of the upright sticks, and insert it firmly in the ground, with its upper notch facing the sapling, and at about four feet distant from it. Bend down the "springer," and by its force determine the required length for the draw-string attaching one end to the tip of the sapling, and the other near the end of a catch piece, the latter having its bevelled side uppermost. The wire noose should then be attached to the draw-string about six inches above the catch-piece. The pen should now be constructed as previously directed.

Its entrance should be on the side _furthest_ from the springer, and should be so built as that the peg in the ground shall be at the back part of the enclosure. The pen being finished, the trap may be set.

Insert the bait stick with bait attached into the square notch in the side of the upright peg; or, if desired, it may be adjusted by a pivot or nail through both sticks, as seen in our ill.u.s.tration, always letting the baited end project toward the [Page 50]

opening. Draw down the catch piece, and fit its ends into the notches in the back of the upright peg and extremity of the bait-stick.

By now pulling the latter slightly, and gently withdrawing the hand, the pieces will hold themselves together, only awaiting a lift at the bait to dislodge them. Adjust the wire loop at the opening of the pen, and you may leave the trap with the utmost confidence in its ability to take care of itself, and any unlucky intruder who tries to steal its property.

Most of the snares which we shall describe are constructed from rough twigs, as these are always to be found in the woods, and with a little practice are easily cut and shaped into the desired forms. If desired, however, many of them may be whittled from pine wood like the foregoing, and the pieces carried in a bundle, ready for immediate use. In either case, whether made from the rough twigs or seasoned wood, it is a good plan to have them already prepared, and thus save time at the trapping ground when time is more valuable.

THE PORTABLE SNARE.

This is simply a modification of the snare just described, but possesses decided advantages over it in many respects. In the first place, it requires little or no protection in the shape of an enclosure.

It can be set in trees or in swamps, or in short in _any_ place where an upright elastic branch can be found or adjusted. Like the foregoing, it is to be commended for its portability, fifty or sixty of the pieces making but a small parcel, and furnishing material for a score of traps. We call it the "portable snare"

partly in order to distinguish it from the one just described, but chiefly because this particular variety is generally called by that name in countries where it is most used.

It is composed of three pieces, all to be cut from a shingle or thin board. Let the first be about eight inches long, and three-quarters of an inch in width. This is for the upright. An oblong mortise should be cut through this piece, one inch in length, and beginning at about an inch from the end of the stick. Three inches from the other end, and on one of the broad sides of the stick, a notch should be made, corresponding in shape to that shown in our ill.u.s.tration. The bait stick should be four or five inches long, one end fitting easily into the mortise, where it should be secured [Page 51]

by a wire or smooth nail driven through so as to form a hinge, on which it will work easily. On the upper side of this stick, and two inches distant from the pivot, a notch should be cut, similar to that in the upright. The catch piece should be about two inches in length, and bevelled off to a fiat edge at each end. This completes the pieces.

[Ill.u.s.tration]

To set the trap, it is only necessary to find some stout sapling, after which the upright stick may be attached to it close to the ground, by the aid of two pieces of stout iron wire, twisted firmly around both. It is well to cut slight grooves at each end of the upright for the reception of the wires, in order to prevent slipping.

Tie a strong piece of twine around one [Page 52]

end of the catch piece, knotting it on the beveled side. Cut the string about two feet in length, and attach the other end to the tip of the sapling. Adjust the bait stick on its pivot. By now lowering the catch piece, and lodging the knotted end beneath the notch in the upright and the other end in the notch on the bait stick, the pieces will appear as in our drawing. Care should be taken to set the catch pieces as slightly as possible in the notches, in order to insure sensitiveness. At about four inches from the catch piece, the wire noose should be attached and arranged in a circle directly around the bait. By now backing up the trap with a few sticks to prevent the bait from being approached from behind, the thing is complete, and woe to the misguided creature that dares to test its efficacy. By adjusting the drawstring so far as the upper end of the catch piece, the leverage on the bait stick is so slight as to require a mere touch to overcome it; and we may safely say that, when this trap is once baited, it will stay baited, so far as animal intruders are concerned, as we never yet have seen a rabbit or bird skilful enough to remove the tempting morsel before being summarily dealt with by the noose on guard duty.

For portability, however, the following has no equal.

THE "SIMPLEST" SNARE.

This is one of the most ingenious and effective devices used in the art of trapping; and the principle is so simple and universal in its application to traps in general as to become a matter of great value to all who are at all interested in the subject. There is scarcely a trap of any kind which could not be set with the knotted string and bait stick, at the expense of a little thought and ingenuity. The principle is easily understood by a look at our engraving, which probably represents the _simplest_ twitch-up it is possible to construct. A stout wooden peg, having a hole the size of a lead pencil near the top, is driven firmly into the [Page 53]

ground. The "knot" is made on the end of the draw-string, and pa.s.sed through the hole in the peg from behind, being secured in place by the insertion of the bait stick in front. The latter should be about four inches long, and should be inserted very lightly,--merely enough to prevent the knot from slipping back. The noose should be fastened to the draw-string six or seven inches from the knot, and arranged in front of the bait at the opening of the pen, which should be constructed as previously directed. The peg should be about six inches long and the hole should be made with a 1-3 inch auger. Dozens of these pegs may be carried without inconvenience, and utilized in the same number of snares, in a very short time.

We have already described the so-called "portable snare;" but, for portability, there is no noose-trap to be compared with the above.

We give also a few other applications of the same principle.

[Ill.u.s.tration: Method No. 1]

In the second example, a horizontal stick is used instead of the peg, the hole being made in its centre. Its ends are caught in notches in opposite sticks at the back part of the pen, and the noose arranged at the opening.

[Ill.u.s.tration: Method No. 2]

Again, by a third method (see engraving next page), these notched sticks may be driven into the ground first, and a row of twigs continued on them on both sides, thus leaving a pa.s.sageway between as represented in the ill.u.s.tration. A noose may then be set at each opening, with the bait in the middle; so that, at whichever side it is approached, the result is the same, besides affording a chance of securing two birds at the same time.

THE QUAIL SNARE.