Ethnology of the Ungava District, Hudson Bay Territory - Part 9
Library

Part 9

I remember an instance occurring opposite Fort Chimo. A kaiak had been left until the ice in the river was firm enough to enable the vessel to be brought over on it to the station. One day a woman declared that she could see a wolf tearing the skin from the frame. It was scarcely credited, but in the course of half an hour the wolf started across towards the post. It was met and showed some disposition to attack, but was shot. I watched to see where the men went to look at the kaiak, and when they reached the place I was astounded that the woman could discern even the kaiak at such a distance.

The spear used for white whales and large seals consists of a wooden shaft of 6 or 8 feet in length, having a projection on the side, made of ivory and shaped like the fin of a fish. This fin-shaped piece rests against the forefinger, while the remainder of the hand grasps the shaft. The lower end of the shaft terminates in a piece of bone or ivory of 1 to 1? inches in diameter. (Fig. 67.) A socket is made in the end of the bone portion, and the wooden shaft is nicely fitted into it and fastened either by thongs or rivets. At the farther end of the bone head is a thimble-shaped hole gouged out, and into this a short piece of straight bone or ivory is fitted, having the ends so shaped that they will work smoothly into the hole at the end of the bone head of the spear. The farther end of this bone shaft is so shaped that it will work into the bone or ivory portion of the piece into which the spear point is fastened. The point is shown in the accompanying figure (Fig. 68) and is not much varied in general shape. There are two joints between the spear point and the bone shaft head. This enables the spear-point to become easily detached when the game is pierced. If this were not so, the bone or ivory would soon break with the violent motions of the animal, and the implement would be rendered useless until repaired.

Thongs connect the various parts together, also connecting them with the main shaft of the spear. A long line, usually left lying in a coil just in front of the hunter, gives ample scope for play until the animal is exhausted. If the sea is rough or the hunter unable to cope with the quarry, the float, to be described below, is thrown over and the seal or whale allowed to take its course, the hunter following and endeavoring to hara.s.s the animal as much as possible, giving it a stab with the hand spear whenever occasion offers.

In addition to the whale or seal spear, the hand spear, float, and paddle, the kaiaker may have a wooden shaft, on the end of which are three p.r.o.ngs of barbed iron, each p.r.o.ng 8 to 10 inches long, and set in the form of a divergent trident. With this implement, small seals and the white-coated young are killed. Birds, too, are sometimes speared with this trident.

The hand board, or implement with which certain spears are hurled, is a piece of wood of such shape that a description will give but little idea of its form. It is about 14 inches long, flat, and has a groove on one side into which the rear end of the spear shaft rests, and is supported by the three fingers of the hand while the index finger fits into a hole cut through the board, of the shape to accommodate that digit. The tip of the finger rests against the shaft of the spear. Other notches are cut along the side of the board to enable the three fingers to lie in position to give a firm grasp on the end or handle of the board. The thumb turns over so as to lie directly on the spear, to steady it, while the other fingers give the spear the necessary straight motion when the arm is drawn back and raised nearly perpendicularly. When it reaches that position the motion is arrested and the fingers release the implement held along the groove. The hand board or thrower is retained and the spear recovered if the object has not been struck. If the aim was good the spear remains attached to the struggling animal, and the hand board is quickly placed under one of the thongs stretched across the top of the kaiak. The paddle is held in the left hand and ready for instant use.

The paddle is quite heavy and of variable length, having long, narrow blades, which are alternately dipped into the water. The use of the paddle requires some practice before one becomes accustomed to it. When in use the paddle rests on the edge of the hoop, forming the rim of the hatch, and moves along it in the motion of propulsion.

As the paddle dips into the water the dripping often causes the clothing to become wet. To obviate this, these people use a piece of plaited rope or skin to slip nearly to the beginning of the blade. This causes the dripping to fall outside of the kaiak; and in cold weather is very necessary, unless heavy mittens of tanned sealskin be worn.

An implement used for hooking into the body of a sunken seal or whale is made in the following manner: A piece of wood is prepared about 8 feet long and three-fourths of an inch thick, having a width of an inch and a half. The lower end of this has a strong hook made of stout iron set into it. Along the inner edge of the wooden shaft two or three notches are cut. The end near the person has a V-shaped notch cut into it. This is used for all the purposes of a boat hook, and also to retrieve a sunken animal. A weight is attached to near the hook end to keep the shaft perpendicular in the water. A line of sufficient length is attached to it. The hunter has marked the locality, and with the hook "feels" the bottom for the game. When found the hook is jerked into the skin and the object brought to the surface. The staff is very necessary while the kaiak is being moved through narrow channels among the ice fields. It is, in fact, available in many instances where the paddle would, from its length, be useless. The kaiak outfit would be incomplete without the hook.

A young man starts out in life with a gun and ammunition with which to procure game. If he has the energy to become a successful hunter he will soon be able to make a kaiak, and thus procure the marine mammals whose skins will afford a covering for an umiak and in the course of time additional skins for a tent. These possessions usually come in the order laid down, and when they are all procured he is generally able to have others under his direction a.s.sist in transporting them from place to place; and thus he becomes the head of a gens or family, including his brothers and sisters with their husbands, wives, and children. These usually move in a body wherever the head may dictate, and all their possessions accompany them on the journey. Brothers often live together and own the tent and umiak, the remainder of the household affairs being considered as individual property and not to be used by all without permission.

Some of the men are too improvident to prepare these skins when they have the opportunity, and thus they are unable to own a kaiak, which prevents them from providing themselves with the umiak and tent. These persons must live with others or dwell by themselves and pa.s.s a miserable existence, scarcely noticed by their fellows even during a season of abundance.

The collection contains one full-sized kaiak, with all its fittings, and their models, including a toy kaiak cut from a walrus tusk. The model is just 9 inches long and quite perfect in form. The double-bladed paddle accompanying is made from the same material, and is six inches long.

ON LAND.

The universal means of transportation on land is the sled, drawn by dogs. The number of dogs used to draw a sled varies according to the distance to be traveled, the character of the country, the condition of the animals, and the weight of the load to be drawn. From one to twenty dogs may be used. The common team for general purposes is seven or nine animals.

The method of constructing sleds differs slightly in different parts of the region, and then only where the material may be difficult to obtain or a heavy sled may not be needed. A tree of a suitable size is selected, generally larch, because of its greater strength, although somewhat heavier than the spruce.

It is necessary, for greater strength, that each runner be of a single piece of timber. The length of the runner is from 12 to 16 feet; the height varies from 10 to 12 inches. The piece must be as nearly free from knots and crossgrain as possible, for these defects render the wood very brittle during cold weather. The runners are roughly hewn at the place where originally cut, and, when needed, they are brought to the temporary camping place of the Eskimo, and there dressed with plane and saw to the required form. The bottom of the runner is usually 2 to 3 inches thick, gradually becoming thinner by one-half an inch to an inch toward the top. This enables the sled to make a wider track at the bottom and encounter less friction of the runner sides against the snow crust. The curve at the forward end is long and very gradual. There may be as much as 3 feet of the curved part, which rises above the level of the lower edge of the runner. This enables the sled to creep easily over any obstruction. The runners are now placed parallel, separated by a distance of 14 to 16 inches, and on these are fastened crossbars 3 inches wide, of sufficient length to allow about an inch to project over the outer edge of each runner. Near the ends of these slats is cut a notch on each edge. Sometimes a hole is also bored through the slat between the notches. These are for the purpose of fastening the slats to the runners. A sufficient number having been prepared, and placed 1 or 2 inches apart, they are now laid on the flat top of the runner. Holes are bored through the top of the runner to correspond with the holes and notches of the slats. Through these and over the slats a stout piece of heavy sealskin line is threaded, and so on through and over the slats and runner until it is firmly fastened. The line must be well soaked in water to render it flexible and allow it to stretch, otherwise the joints where it was tied would soon work loose. The line shrinks while drying, and draws as tight as though made of the best iron. No metal is used, for the reason that it would snap as easily as chalk during cold weather. The use of the thongs in binding the slats to the runners allows freedom to the motion of the sled when pa.s.sing over inequalities of surface, where a rigidity of the sled would soon cause it to break.

The bottom of the runner is shod with iron brought by the traders for that purpose. It is simply extra-wide hoop-iron and of a width to fit.

It is fastened on with screws, the heads of which are countersunk.

Another kind of shoe is put on when traveling in very cold weather.

A swampy track is searched for soil of half-decomposed vegetation and pure humus, as nearly free from sand and gravel as possible. It must possess certain qualities or it may not have the requisite strength--much, I presume, as mortar often requires to be tempered with more or less lime or sand when it is too rich or too poor. The Eskimo tempers his mortar with the almost impalpable soil found under the larger spreading trees of the forest. It is the slowly decomposed vegetation fallen from branches and trunks. The manner of preparing it is as follows: A large kettle is partially filled with the material and heated to the boiling point, being constantly stirred, and while yet cool enough all coa.r.s.e sticks, gra.s.s blades, pebbles, etc., are carefully removed as the fingers discover them in working the mortar.

The sled is turned over with the bottom of the runner up. The mud is now applied by the hands, a couple of pounds being taken and pressed on the runner, which has previously been wetted. This process of adding to the runner is continued until it attains an additional depth of 3 or 4 inches and a width of 3 to 5 inches. It now resembles the rail of a stairway. When it has been thoroughly gone over to fill up any inequalities the sled is set aside in order that the mud may freeze solid. The sled must be handled with care, as the least jar or jolt will break the "setting" mud. After it is frozen the owner takes a plane and planes it down to the proper shape and smoothness. It is somewhat difficult to describe the shape in words, unless it be compared to the upper part of the =T= rail of a railroad inverted--neither rounded nor flat, but so fashioned as to give the best bearing surface with the least friction. When the plane has finished its work the color of the mud is a rich chestnut brown. The builder now takes water in his mouth and spirts it in a spray along the mud. As soon as the water touches the runner it must be spread evenly with a hand incased in a mitten of reindeer skin, rubbing back and forth until the runner looks like a bar of black gla.s.s. The sled is then ready for use. Great care is necessary to avoid rocks or stones, as these cut the polished mud and roughen it.

If a sudden lurch causes a portion of the mud to drop out the piece is frozen on again by means of water, or if crumbled a piece of ice is cut to the shape and caused to adhere by water freezing it to the runner.

It is not often that one may find a sled shod with bone, as is the custom with the Eskimo farther north, and especially farther west. The only instance where I have seen bone used was by some of the people from the western extremity of Hudson strait. These had only a portion of the curve and a part of the runner shod with bone and pieces of reindeer horn, secured to the runner by means of pegs.

The greatest objection to the use of mud is that a few hours of warmth may cause it to loosen and render it worthless. The polish suffers when traveling over rough ice, and especially where sand has drifted from some exposed bank to the surface of the snow. This causes very hard pulling, and soon roughens the running surface of the sled. To repair such damage the native stops, at a convenient place, to obtain water, which is spirted on the runner and rubbed evenly until it acquires a thickness of one-eighth of an inch. This coating of ice may last for the entire day of travel where the "roads" are good.

The harness for the dogs consists of two large nooses, placed one above the other. These are joined by two perpendicular straps of 4 or 5 inches in length at a sufficient distance from the end to allow the head of the dog to pa.s.s through so that one noose will lie along the back and the other between the forelegs. At the rear ends of the nooses is a long thong of the heaviest sealskin of variable length depending on the position or place the dog is to have in the team. The body harness is made of sealskin, with or without the hair on, stout canvas, or other material which may be convenient. Thin undressed sealskin makes the best harness, and is not so liable to chafe the neck of the animal. The trace attached to each dog is generally of stout sealskin thong cut three-eighths of an inch wide, and the corners are carefully pared until the trace in form resembles a hoop for a small keg. The trace varies from 10 to 30 feet in length, and is attached to a longer but much stouter thong of heavier sealskin or walrus hide prepared in the form described for the trace. The thong to which all of the traces of variable lengths are fastened is termed the "bridle." The bridle has, usually, apiece of ivory, called "toggle," at the end farthest from the sled. A few inches back of the toggle is a short piece of stout thong plaited in the bridle end. This thong has a slit cut in the farther end.

It is pa.s.sed through slits cut in the end of each trace and then looped on the toggle. It will now be understood that the traces all start from one place, but their different lengths give different positions to the dogs of the team so that they may move freely among rough pieces of ice without interfering with each other. This has some advantages, but it necessitates watching the traces as they are liable to catch around any projection above the surface.

The bridles are also of varying lengths, from 15 to 40 feet. The rear end has two stout thongs plaited into it, forming a loop for each thong.

These are known as the "yoke," and are looped over toggles, one on each inner side of the runner.

Any load to be carried on the sled is usually placed so as not to project much over the side, for in deep snow, with a crust too weak to support the weight, it would simply act as a drag and seriously impede travel if not entirely stop it. The load must also be distributed to the best advantage along the sled so as not to have too great a weight at either the front or rear, although generally a heavier portion is placed behind to allow the sled to steer or follow. The runners are so low that the sled seldom upsets unless the ice is very rough, in which case it often requires two men to attend to it, another to free the traces from obstructions, and a fourth to lead or drive the dogs. A smaller number render traveling under such conditions very tedious.

The driver is always armed with a whip (Fig. 60). There appear to be as many kinds of whips as there are individuals using them. Each whip characterizes, in a manner, the person who makes it. A great amount of ingenuity is expended in preparing the lash, which is simply indescribable. The handle of the whip is from 9 to 11 inches in length and shaped somewhat like the handle of a sword without the guard.

A stout loop of thong is affixed to the stock above where the hand grasps it. This loop is thrown over the wrist to prevent the weight of the whip drawing the stock from the hand and also to retain the whip when it is allowed to trail behind.

[Ill.u.s.tration: FIG. 60. Dog whip. {}]

At the farther end of the stock a portion of the wood is cut out to allow the insertion of the end of the lash which is fastened by means of finer thongs. The b.u.t.t end of the lash is five-sixteenths of an inch thick and nearly 2 inches wide. It is composed of eight heavy thongs plaited in a peculiar manner, depending on the number of thongs used and the fancy of the maker. The thongs are plaited by inserting the end of each thong through a succession of slits cut at the proper distance and so matted together that it is difficult to determine the "run" of the thong. The size decreases from the handle by dropping out a strand until at 18 inches from the stock only four thongs are left, and these form a square plait for a foot in length. This square form is succeeded by only two thongs which make a flat plait of 2 feet in length. At the end of this a simple piece of heavy thong completes the lash. The length of a whip may be as much as 35 feet, weighing 3 or 4 pounds. Some of the natives acquire a surprising dexterity with this formidable weapon, often being able to snip the ear of a particular dog at a distance of the length of the whip. I have known them to snap the head from a ptarmigan, sitting along the path of the team. Children practice with the whip as soon as they can manage it.

The Eskimo dog fears nothing but the whiplash. They attack each other with savage ferocity, and several dogs may be engaged in terrific battles, yet the swish of a whip or even a stick thrown hurtling through the air is sufficient to cause them to slink off in abject terror, whining piteously in fear of the expected lash.

The weight or load put upon a sled may be as much as 1,200 pounds. The character of the road alone determines the weight, number of dogs, and rate of travel. The latter may average over a smooth surface 5 miles hourly for twelve hours continuously, excluding the few minutes given the dogs to "blow" (rest), etc. I knew an instance where three men with empty sled and seven dogs traveled 94 miles in eighteen hours. I have gone 19 miles in three hours; and again I have known only 3 or 4 miles to be made in ten hours, through rough ice or deep, newly fallen snow.

The disposition and condition of the dogs chiefly determines the number attached to the sled. With these animals there is the same difference as is to be found in horses or other beasts of draft. Some are energetic and well-behaved; others as stubborn or lazy as is possible. Strange dogs in the team are liable to be pitched upon by all the others and with the long traces ensues such an entanglement of lines, dogs, and flying snow as is difficult to conceive. The good qualities of the driver are manifested by his ability in keeping the dogs in order and showing promptness in separating them when quarreling. Fighting among the dogs can always be prevented by the driver keeping the dogs in proper position.

WEAPONS AND OTHER HUNTING IMPLEMENTS.

These people are now provided with firearms, which have entirely superseded the bow and arrow.

The bow formerly used in this region appears to have been similar to the one obtained from a party of East Main Innuit, who made their way to Fort Chimo. This bow has accordingly been figured and described (Figs.

61 and 62--90137).

[Ill.u.s.tration: FIG. 61.--Bow. East Main Eskimo (back).]

[Ill.u.s.tration: FIG. 62.--Bow. East Main Eskimo (side).]

It is made of larch wood and has a backing of eight double strands of twisted sinew. This sinew is in one piece sixteen times the length of the bow. One end is looped and pa.s.sed over one "nock" of the bow and carried back and forth from nock to nock eight times. This backing has two turns of twist put in from the middle to increase its elasticity, and is lashed to the middle of the bow with a stout thong of reindeer skin. The bowstring is of twisted sinew with a loop at each end.

With this bow were seven arrows. Three of these are for shooting reindeer and wolves. They have an iron point set in a short foreshaft of reindeer antler, and a wooden shaft about 16 inches long (Fig. 63).

Three more are pointed with large nails, one of which has been beaten to a chisel-shaped point (Figs. 64 and 65). They are intended for large game at short range, or for small game, such as hares and ptarmigan.

These six arrows are feathered with the tail feathers of the raven.

The last arrow is a simple shaft, without feathering or head, and is intended for small game, such as a wood hare crouching under a spruce tree, or the little red squirrel on the top of a low tree.

In drawing the bow, the Innuit invariably hold the arrow between the middle two fingers of the right hand, and the string is drawn with all four fingers, and released by straightening them.

The bow and arrows are carried in bow case and quiver fastened together and slung on the back. Fig. 66 represents a model (No. 3257) of such a bow case. The bow case is made of buckskin and is of sufficient length to contain the bow, excepting the extreme end, which is left projecting for convenience in handling. The case is tied around the bow at the projecting end. The quiver is attached to the bow case and contains two models of arrows for shooting large game. The arrows are tipped with leaf-shaped pieces of tin. They are feathered with portions of feathers apparently taken from the tail of a raven. The mouth of the quiver is also drawn up with a string to prevent the loss of arrows. I have not seen the Eskimo of Hudson strait use such a cover for their bows and arrows, but the opportunities to observe them are very limited, as few are used. I am led to conclude that only the poorer individuals of either locality have the bow and arrow at the present day.

[Ill.u.s.tration: FIGS. 63, 64, and 65.--Arrows. East Main Eskimo.]

I have already described the large harpoon used for striking white whales and large seals from the kaiak. A short-head spear (Fig 67, No.

90164) is used for dispatching wounded seals or white whales, or for killing white whales when they have been driven into a shallow arm of the sea when the tide ebbs and leaves them partly uncovered. It has a short wooden shaft with a ferrule of ivory, holding a short ivory loose shaft, kept in place by thongs, on which is mounted a toggle head like that used on the big harpoon. The line is either attached to the kaiak or to a small float made of the inflated intestine or skin of a seal.

The toggle heads for these spears are made of ivory, and fitted with iron blades (Fig. 68). I have already referred to the large sealskin float in describing the kaiak.

Fig. 69 (No. 3531) is such a large sealskin float or a va tuk. The skin is removed from the body by skinning around the gums and carefully taking out all the flesh and bones through this orifice. As the operation proceeds the skin is turned back and at the completion of the work is inside out. The flesh side, now the exterior, is carefully sc.r.a.ped to free it from all fleshy matter. The hind flippers are cut off at the ankle and the skin either sewed or stoutly wrapped with thong.

The fore flippers are usually left attached to the skin after the flesh has been sc.r.a.ped from them. The skin is now inflated with air and hung up to dry. In a few hours it is turned with the hairy side out and again inflated for awhile. The mouth and all other openings in the skin are carefully sewed up. A large b.u.t.ton of ivory, shaped much like a pulley, nearly 2 inches in diameter, is put where the mouth of the skin is and a portion of the skin carefully wrapped around it, thongs of sealskin tightening the moist skin in the groove of the mouthpiece. This piece has a hole about one-third of an inch in diameter bored through it. The hind flippers and tail have a stick of 2 or 3 inches in length placed within the skin and are then firmly bound around the stick, which serves to stop up any hole and also to furnish a handle by which to drag or hold the float. The hole in the mouth-piece is plugged with a stopper of wood. When the float is wanted for use the skin is inflated. When inflated the float has a diameter about two-thirds the length. If it is to be attached to a tracking line the float is fastened by the stick, which is secured within the skin of the hind flippers and dragged backwards. The function of the float in this instance is to prevent the tracking line from becoming "fouled" among the rocks and stones of the beach along which the line runs in towing a boat (or umiak). In a similar manner it is affixed to the harpoon line used for large marine mammals, such as the white whale and the larger species of seals. This float not only r.e.t.a.r.ds the flight of the speared animal, but it serves to mark the spot where it sinks, for at certain seasons the seals sink as soon as they die. A speared animal always sinks more quickly than one shot dead with a ball, probably because its struggles are more prolonged in the first instance and exhaustion of breath is more complete.

[Ill.u.s.tration: FIG. 66. Bow case. East Main Eskimo.]

The hair of the animal whose skin is intended for a float is sometimes sc.r.a.ped off before the skin is removed from the body, otherwise it may be left until the skin is partly dry and then be shaved off. The manner of loosening the hair is similar to that used by butchers of hogs, only that the boiling water is poured on and a small patch of hair pulled off at a time, instead of submerging the entire animal. The hair from the green skin must be carefully pulled out or else the black scurf adhering will be detached and thus render the skin less nearly waterproof.

The skins or bags used for holding oil and fat are prepared in a similar manner, excepting that the hair is left on the skin and the hairy side left within. The oil and fat are put in the skin at the posterior end and it is then tied up like a float. The largest sealskins are used for oilbags, and may contain as much as 300 pounds of fat or oil.